How to set the caller ID for IP-to-E1 calls 2020-06-05

Technical Guides

How to set the caller ID for IP-to-E1 calls

  • This instruction guide aims to show how to set the caller ID for IP‑to‑E1 calls. In this guide, MTG200 E1 VoIP Gateway is used as an example to illustrate the configurations, which will also apply to other TG products from Dinstar. There are 2 modes for setting the caller ID, namely "Bind Port" and "Bind Route". Users can choose one of them based on the actual application scenario. We will show below how to use these two modes to set the caller ID respectively.
    Note :
    MTG1000 does not have this feature.
    If the current firmware version of the device does not have this feature, please update it.
    The two modes cannot be applied simultaneously to each E1 port.
    MTG 0 port is connected to an E1 cable and has a caller ID range of 22900600 – 22900615 and 22900617-22900699. When calls go from IP to PSTN, use any ID from the range to replace the original caller ID.
    c1.png

    Mode Bind Port

    The "Bind Port" mode relies on the E1 port. As long as calls pass through this E1 port, all caller IDs will be replaced.
    1. Create the caller pool
    Click Number Filter → Caller Pool.
    Select 0 as the caller pool identifier.
    c-2.png
    The originating caller ID is set to 22900600 and the number of IDs is set to 16, meaning the caller ID range is 22900600-22900615. MTG will randomly select a caller ID from the range to replace the original.
    2. Add the port number
    Click PSTN Group Configuration → Port Number
    Add a rule for the port number. That is, set the binding pool to “0” (which means bind the caller pool “0” to E1 port 0). And set the outgoing caller type to “Replace”, meaning the caller ID of IP‑to‑PSTN calls will be replaced.
    c3.png
    Note: The link number priority is higher than the link pool. In other words, if the link number is set as a specific number, all caller IDs of IP‑to‑PSTN calls will be replaced by this link number. In this case, it is not necessary to set the link pool.
    c-4.png
    For example, if you set 22900600 in the Link Number field, all CIDs (caller IDs) will be replaced with 22900600 as follows:

    Routing Link Mode

    The "Bind Route" mode is based on the IP->PSTN routing rule. You can set a condition to determine which call CID will be replaced and which will not.
    1. Create the caller pool
    Click Number Filter → Caller Pool.
    Select 0 as the caller pool identifier.
    The originating caller ID is set to 22900600 and the number of IDs is set to 16, meaning the caller ID range is 22900600-22900615. MTG will randomly select a caller ID from the range to replace the original.
    2. Create the whitelist
    Click Number Filter → Caller ID Whitelist.
    Select 0 as the caller whitelist ID, and set the Caller Number to ‘.’. The dot indicates all caller numbers.
    3-1.png
    3. Create the filter profile
    Click Number Filter → Filter Profile.
    Create filter profile 0, set the caller whitelist ID to 0 (this whitelist was configured at step 2), and set the caller pool for the whitelist to 0 (this caller pool was configured at step 1).
    3-2.png
    3-3.png
    4. Create the IP->PSTN route
    Click Call Routing → IP Routing->PSTN
    Create a routing rule for IP->PSTN calls. Choose 0 as the filter profile ID (this filter profile was configured in step 3). You can also set the caller/callee prefix as a condition to filter the caller number. The point ‘.’ means match all caller numbers.
    3-4.png
    3-5.png