How to Force Airtel Card to Use VoLTE 2020-06-15

Technical Guides

How to Force Airtel Card to Use VoLTE

  • The LTE module "EC25E" is popular in India, and it works well on 2G/3G/4G networks and JIO's VoLTE network. As the operator’s network improves, Airtel launched the VoLTE network, but customers encounter a problem with Airtel VoLTE registration. The main reason is that the "EC25E" module has no Airtel‑specific MBN file when VoLTE is selected. This instruction guide aims to show how to force Airtel to use VoLTE. In this guide, UC2000‑VF is used as an example to illustrate the configurations, which will also apply to other Dinstar UC2000 products.
    Note : the EC25E module refers to version EC25EFAR06A06M4G or newer.
    The UC2000‑VF uses the LTE module "EC25E" and has the IP address 172.19.1.20. The Airtel SIM card is inserted into port/module 0 of the UC2000‑VF device.

    Ready Environment

    1. Telnet of UC2000-VF
    Run the "Putty" application and connect to UC2000-VF via IP 172.19.1.20 (refer to the following setting). The default telnet port is 23:
    image001.png
    Note :
    If the connection fails, please click Tolls>>>>>Management page to verify that the Telnet option is enabled on the UC2000-VF side.
    Restart the device for the configuration to take effect.
    image002.png
    2. Open the ADA monitoring window
    Connect to telnet and enter the command "en", then "^ada". Press "Enter" to enter ADA mode as follows:
    image003.png
    Enter the command 53 19 0 0 1 to open the AT monitor of module 0 :
    image004.png
    Note :
    The command format is: cmd 53 19 X Y Z
    X Y denotes the module number range from X to Y. If only one port is enabled, X equals Y. Z means ON or OFF; the value 0 means ON; the value 1 means OFF.
    Z means ON or OFF; the value 0 means ON; the value 1 means OFF.
    For example :
    cmd 53 19 0 0 1 means enable module 0 cmd 53 19 0 0 0 means disable module 0 cmd 53 19 2 4 1 means enable ports 2 to 4.
    3. Open the configuration window 'Config'
    Repeat the configuration described in section 2.1. Then connect to telnet and enter the command "en" then "^config". Press "Enter" to enter Config mode as follows:
    image005.png

    MBN configuration

    1. Set the Airtel APN
    Open the Mobile Configuration page >>> Mobile Configuration, set Airtel’s APN on module 0: airtelgprs.com
    r-1.png
    Notes :
    The APN password must be left blank.
    2. Disable the module's MBN
    In the Config window, enter the command: mobile cmd at 0 at+qmbncfg="deactivate” to disable the MBN of the current module 0.
    image006.png
    Notes :
    The command format is: mobile command to X at+qmbncfg="deactivate"
    X denotes the module number.
    3. Disable automatic MBN
    In the Config window, enter the command: mobile cmd at 0 at+qmbncfg="AutoSel”, 0 to disable automatic MBN of the current module 0 .
    r-2.png
    Notes :
    The command format is: mobile cmd at X at+qmbncfg="AutoSel", 0
    X denotes the module number.
    4. Restart the module
    In the Config window, enter the command: mobile cmd at 0 AT+CFUN =1,1 to restart the current module 0, in order to activate section 3.1.
    image007.png
    Notes :
    The command format is: mobile command at X AT+CFUN=1,1
    X denotes the module number.
    In the ADA window, you will see the following display indicating that module 0 has been successfully restarted.
    image009-.png
    5. Repair the MBN
    After the module 0 starts, enter the command:
    mobile cmd at 0 at+qmbncfg="select","Reliance_OpnMkt” in the Config window to lock module 0 with MBN Reliance_OpnMkt. You can then enter the command twice to confirm the locking operation.
    The goal is to force the Airtel card to use JIO's MBN: Reliance_OpnMkt.
    image008.png
    Notes :
    The command format is: mobile cmd at x at+qmbncfg="select","Reliance_OpnMkt"
    X denotes the module number.
    In the ADA window, you will see the following display:
    6. Restart the module.
    In the Config window, enter the command mobile cmd at 0 AT+CFUN =1,1 restart the current module 0, in order to activate the MBN parameter.
    Notes :
    The command format is: mobile command at X AT+CFUN=1,1
    X denotes the module number.
    In the ADA window, you will see the following display:
    7. Check the MBN status of the module
    After module 0 has started, please check the MBN status.
    In the Config window, enter the command mobile command at 0 at+qmbncfg="list". You can enter the command multiple times to get the exact status.
    image009.png
    Notes :
    The command format is: mobile command at x at+qmbncfg="list"
    X denotes the module number.
    In the ADA window, you will see the following printout, "List",0,1,1,"Reliance_OpnMkt" indicates that MBN Reliance_OpnMkt has been successfully activated.
    image010.png
    Notes :
    1. The print format is : List “List”,X,Y,Z,“xxxxxxxxxxxx”
    X is the list index;
    Y indicates the MBN usage status; 1 means enabled; 0 means disabled.
    Z indicates the MBN activation status; 1 means active; 0 means disabled.
    xxxxxxxxx is the MBN name
    2. If the MBN is not enabled, please wait 2 minutes and then check again.
    3. If it remains inactive, please return to section 3.1 and restart.
    8. Check LTE registration status
    In the Config window, enter the mobile command 0 at+cops? to check the registration status of module 0. You can enter the command multiple times to get the exact status.
    image011.png
    Notes :
    The command format is: mobile command at X at+cops?
    X denotes the channel number.
    In the ADA window, you will see the following printout, "airtel airtel",7 means the SIM card is registered on the Airtel LTE network:
    image012.png
    Notes :
    The print format is: «xxxxxxxxx», Y
    "xxxxxxxxx" means the currently registered network.
    Y indicates the currently registered network mode; value 7 corresponds to the LTE network.
    9. Check IMS registration status
    In the Config window, enter the mobile command 0 at+qcfg="ims" to check the IMS registration status of module 0. You can enter the command multiple times to get the exact status.
    image013.png
    Notes :
    The command format is: mobile command at X at+qcfg=“ims”
    X denotes the channel number.
    In the ADA window, you will see the following printout. The "ims",0,1 indicates that the SIM card is registered on the IMS network.
    If the IMS is not registered, please wait 2 minutes and then check again.
    If it remains unregistered, please return to section 3.1 and reconfigure.
    image014.png
    Notes :
    The print format is: "ims",X,Y
    X indicates the registration mode; the value 0 means automatic.
    Y indicates registration status; 1 means registered while 0 means not registered.
    When the SIM card is successfully registered on the IMS, it means VoLTE is successfully registered!
    10. Check network status during the call
    In the Config window, enter the command mobile command to 0 atd5682878 ; to call
    r-3.png
    Tips
    The command format is mobile command to X atdYYYYYY;
    X denotes the channel number.
    YYYYYY denotes the called number.
    In the ADA window, you will see the following printout.
    r-4.png
    Maintain the call and in the Config window, enter the command mobile to 0 at+cops? to check the current status of module 0.
    r-5.png