How to force the SIM card to use VoLTE 2020-08-10
Technical Guides
How to force the SIM card to use VoLTE
-
- The LTE series EC25-X and EC25-XX modules cover many frequency bands worldwide, but the module supplier has not finished compatibility testing with all operators, so there is still no independent MBN for each operator. For example, the "EC25-AU" frequency corresponds to Australia and Latin America, but there is no MBN for Claro in Argentina.
- While operator networks have improved, VoLTE has been launched, but customers may still encounter the “no VoLTE call” issue. When the SIM attempts to call, it downgrades to 3G or 2G because no independent MBN can be used when VoLTE is selected.
- This instruction guide aims to show how to force the SIM card to use VoLTE. The UC2000-VG GSM VoIP gateway uses the LTE module "EC25-AU" and has the IP address 192.168.34.50. The Claro SIM card is inserted into port/module 2 of the UC2000‑VG device.
- Note: The EC25-AU module refers to version EC25AUFAR06A03M4G or higher.
1. Telnet of UC2000-VF- Run the "Putty" application and connect to the UC2000-VG via IP 192.168.34.50 (see the following settings). The default telnet port is 23:
- Note :
- 1. If the connection fails, please click Tolls>>>>>Management page to check if the Telnet option is enabled on the UC2000-VG side.
- 2. Restart the device for the configuration to take effect.
2. Open the ADA monitoring window- Connect to telnet and enter the command "en", then "^ada". Press "Enter" to enter ADA mode as follows:
- Enter the cmd 53 19 2 2 1 command to open the module 2 AT monitor:

- Note :
- The command format is: cmd 53 19 X Y Z
- X Y denote the module number range from X to Y. If only one port is enabled, X equals Y.
- Z means ON or OFF; the value 0 means ON; the value 1 means OFF.
- For example :
cmd 53 19 0 0 1 means enable module 0 cmd 53 19 0 0 0 means disable module 0 cmd 53 19 2 4 1 means enable ports 2 to 4.3. Open the configuration window 'Config'- Repeat the configuration described in section 2.1. Then connect to telnet and enter the command "en" then "^config". Press "Enter" to enter Config mode as follows:
4. Confirm whether the SIM card supports VoLTE or not- In the Config window, enter the command: mobile cmd at 2 AT+CIREP=1 to enable printing of the current module 2 VoLTE information.
- Note :
- The command format is: mobile cmd at X AT+CIREP=1
- X denotes the module number.
- In the Config window, enter the mobile command "at 2 AT+QVOLTEDBG" to check detailed information for module 2.
- Note :
- The command format is: mobile cmd at X AT+QVOLTEDBG
- X denotes the channel number.
- In the ADA window, you will see the following printout.
- CIREP : 1 means the SIM card supports VoLTE, while 0 means it does not.
MBN configuration
1. Disable the module's MBN- In the Config window, enter the command: mobile command at 2 at+qmbncfg="deactivate” to disable the MBN of the current module 2.
- Tips :
- The command format is: mobile command at+qmbncfg="deactivate”
- X denotes the module number.
2. Restart the module- In the Config window, enter the command: mobile command to 2 AT+CFUN=1,1 to restart the current module 2, in order to activate section 1.
- Tips :
- The command format is: mobile command at X AT+CFUN=1,1
- X denotes the module number.
- In the ADA window, you will see the following display indicating that module 0 has been successfully restarted.
3. Correct the MBN- After starting module 2, enter the command: mobile command to 2 at+qmbncfg="select","ROW_Generic_3GPP" in the Config window to set module 2 so that it is fixed with the ROW_Generic_3GPP MBN. You can then enter the command twice to confirm the locking operation.
- The goal is to force the Claro card to use the common MBN: ROW_Generic_3GPP
- Tips :
- The command format is: mobile command to x at+qmbncfg="select","ROW_Generic_3GPP"
- X denotes the module number.
- In the ADA window, you will see the following display:
4. Restart the module- In the Config window, enter the mobile command to 2 AT+CFUN =1,1 to restart the current module 2, to activate the MBN setting.

- Tips:
- The command format is: mobile command at X AT+CFUN=1,1
- X denotes the module number.
- In the ADA window, you will see the following display indicating that module 2 has restarted successfully.
5. Check the MBN status of the module- After module 2 starts, please check the MBN status.
- In the Config window, enter the command command mobile to 2 at+qmbncfg="list". You can enter the command multiple times to get the exact status.
- Tips :
- The command format is: mobile command at+qmbncfg="list"
- X denotes the channel number.
- In the ADA window, you will see the following printout, "List",7,1,1," ROW_Generic_3GPP" means MBN ROW_Generic_3GPP was selected and successfully activated.
- Tips :
- 1. The print format is: List “List”,X,Y,Z,“xxxxxxxxxxxx”
- X is the list index;
- Y indicates the MBN usage status; 1 means enabled; 0 means disabled.
- Z indicates the MBN activation status; 1 means active; 0 means disabled.
- xxxxxxxxx is the name of the MBN
- 2. If the MBN is not enabled, please wait 2 minutes and then check again.
- 3. If it remains inactive as shown below, please return to section 3.1 and start again.
6. Verify LTE registration status.- In the Config window, enter the command mobile command 2 at+cops? to check the registration status of module 2. You can enter the command multiple times to get the exact status.
- Tips :
- The command format is: mobile command at X at+cops?
- X denotes the channel number.
- In the ADA window, you will see the following printout, " Claro AR Claro AR",7 indicates that the SIM card is registered on Claro's LTE network:
- Tips :
- The print format is “xxxxxxxxx”,Y
- “xxxxxxxxx” indicates the currently registered network.
- Y indicates the currently registered network mode; value 7 corresponds to the LTE network.
7. Configure the IMS setting in the module- In the Config window, enter the command mobile to 2 AT+QVOLTEDBG to check the IMS parameter status of module 2.

- Tips :
- The command format is mobile cmd at X AT+QVOLTEDBG
- X denotes the channel number.
- In the ADA window, you will see the following printout.
- The QNVFR="/nv/item_files/ims/IMS_enable" indicates the IMS parameter status.
- The value of QNVFR 0 means disabled, it should be 1.
- In the Config window, enter the command: mobile to 2 AT+QNVFW="/nv/item_files/ims/IMS_enable", 01 to enable IMS.

- Tips :
- The command format is mobile command to X AT+QNVFW="/nv/item_files/ims/IMS_enable",01
- X denotes the channel number.
- In the ADA window, you will see the following printout.

- Then restart module 2.
- In the Config window, enter the command mobile command 2 AT+CFUN=1,1 to restart the current module 2, in order to enable the MBN setting.

- After the module starts, re‑check the IMS parameter status. The QNVFR value (i.e., 1) in QNVFR="/nv/item_files/ims/IMS_enable" indicates that IMS has been enabled.

8. Check the IMS registration status- In the Config window, enter the command mobile command 2 at+qcfg=”ims” to check the IMS registration status of module 2. You can enter the command multiple times to get the exact status.

- Tips :
- The command format is: mobile command at X at+qcfg=”ims”
- X denotes the channel number.
- In the ADA window, you will see the following printout. The "ims",0,1 indicates that the SIM card has registered on the IMS network. If IMS is not registered, please wait 2 minutes and check again.

- Tips:
- The print format is: "ims",X,Y
- X indicates the registration mode; the value 0 means automatic.
- Y indicates registration status; 1 means registered while 0 means not registered.
- Once the SIM card is successfully registered on IMS, you can test a call to prove it.
9. Check the network status during the call- In the Config window, enter the command mobile command 0 atd8929644377; to call

- Tips :
- The command format is: mobile command at X atdYYYYYY;
- X denotes the channel number.
- YYYYYY denotes the called number
- In the ADA window, you will see the following printout.

- Keep the call and in the Config window, enter the command mobile to 2 at+cops? to check the current status of module 2.

- In the ADA window, you will see the following printout, "Claro AR Claro AR",7 means the SIM card remained on the Claro LTE network and did not drop after switching to the 2G/3G network.

- The test proved that the SIM card now uses VoLTE!
