What is a session controller (SBC)? Part III: High Availability 2022-12-16

VoIP knowledge

What is a session controller (SBC)? Part III: High Availability

  • SBC is the acronym for Session Border Controller — a network element deployed to protect SIP-based VoIP as well as a key network element in NGN/IMS networks and enterprise audio/video systems. High Availability (HA) is a network solution used to ensure that planned or unplanned outages do not interrupt service. In an HA implementation, SBC session controllers are deployed in pairs to provide continuous high availability for interactive communication services. Implementing HA ensures system stability without interruption in the event of a service failure.
    To ensure HA is achieved, many strategies are used in various ways. Generally, good hardware design and intelligent software detection are required to ensure system stability. The high availability of the Dinstar SBC can be achieved in seven ways.
    Redundant design of the device Active/Standby Mode Intelligent Call Routing Quality of Service (QoS) Voice Quality Monitoring Reporting Control & Bandwidth Limitation Warning Monitoring
    Conception redondante du dispositif
    The principle of redundancy is that if a component of a /system/device fails, the /system/device continues to operate because alternative paths are available to keep it running. Therefore, it is important to have many redundant components that significantly improve the reliability of the /system/device.
    The SBC, in some models, supports an integrated design with an 8‑core Matrix processor. The SBC supports 1+1 power redundancy and AC/DC power. The SBC adopts a dual‑power balanced load design; when one power module fails, the other takes over to ensure services are not affected. The SBC supports aggregation of two network interfaces. These two interfaces share an IP address and a MAC address. Network aggregation provides performance and redundancy improvements by increasing throughput and bandwidth. If one interface is out of service or disconnected, the other will operate.
    Active/Standby mode
    In general, the active‑standby mode is considered the most essential feature of HA. HA requires an SBC device to be configured as the primary device, and an identical SBC device to be configured as the secondary device. In normal operation, the primary SBC is in Active state, and the secondary SBC is in Standby state. If the primary device loses connectivity, the secondary SBC switches to Active mode and assumes the configuration and role of the primary, including the configured interface IP addresses.
    The Dinstar SBC not only supports active/standby mode, it also supports real‑time data synchronization of the two devices, BFD heartbeat detection, and detection time granularity (from 30 ms to 100 ms). Thus, when active and standby statuses change, the user service is not affected.
    SBC_HA_1.png
    Intelligent Call Routing
    Intelligent call routing is closely linked to HA. It can increase productivity by assigning agents to customers to optimize system resources. The Dinstar SBC supports intelligent and flexible routing policies, routing calls by weight, time, number, priority, custom number profile, etc., providing users with reliable and efficient fault‑tolerance solutions. The Dinstar SBC also supports multi‑line load balancing and master‑standby redundancy to improve high availability.
    SBC_HA_2.png
    Quality of Service (QoS)
    Quality of Service (QoS) is a critical factor for VoIP. QoS refers to the use of mechanisms or technologies that act on a network to control traffic and ensure the performance of critical applications with limited network capacity. It allows organizations to adjust overall network traffic by prioritizing specific high-performance applications.
    QoS network technology works by marking packets to identify service types, then configuring routers to create separate virtual queues for each application based on their priority. As a result, bandwidth is reserved for critical applications or sites that have received priority access.
    The SBC provides comprehensive QoS policies that can prioritize signaling, voice, and video data, ensure transmission performance such as latency, jitter, network congestion, and packet loss rate, and improve voice and video quality.
    Voice quality monitoring
    Voice quality monitoring allows examination of each source IP address and visualization of a range of MOS scores, RTP streams, jitter, loss, and out‑of‑order packets. Thus, the SBC enables the network administrator to have a complete view of traffic as it traverses the network and adjust resources based on performance thresholds.
    The SBC can monitor and analyze in real time the audio quality of each call, including network jitter, packet loss rate, latency and other network indicators during the call, greatly improving user efficiency and enabling quick problem detection.
    And for unfavorable network conditions, the SBC provides packet loss compensation, dynamic jitter buffering, silence suppression, comfortable noise generation, RTP redundancy, and other voice enhancement technologies to deliver the best user experience.
    SBC_HA_03.png
    List of warning categories
    SBC_monitor_1.png
    Signaling control & bandwidth limiting
    The SBC supports traffic overload protection, which can limit SIP trunk traffic and automatically trigger flow control when the system reaches an overload state. The SBC can also automatically adjust the amount of services based on CPU usage and ensure a certain service connection rate as well as long‑term stable operation of the device.
    Protection against overload
      sbc-p10.png sbc-p11.png

      Q : What causes traffic overload?

      R : Major events are the most common triggers, such as Black Friday in the United States, large gatherings, or attacks triggered by negative news. A sudden spike in traffic due to a data center power outage or network failure is also a frequent trigger source.

      Q : How does the SBC prevent traffic overload?

      R : The SBC can intelligently sort traffic by user level and business priority, with strong overload resistance: 3× overload, activity will not be interrupted. Features such as traffic limiting/control, dynamic blacklist, registration/call rate limiting, etc., are available.
    Alert Monitoring
    Alert monitoring is an essential component of all service systems, and a perfect alert monitoring function can greatly improve system reliability and safety, preventing failures that cause service interruptions. With alert monitoring, the repetitive work of O&M staff can be significantly reduced. By defining monitoring data rules, O&M staff can control the system health at any time.
    The DINSTAR SBC offers a wide range of monitoring capabilities. It can monitor in real time the core components of the system, service status, system processes, security logs and other aspects. The SBC supports threshold customization; once the threshold value is reached, a warning can be displayed in the Web GUI, and you can view detailed information about the current warning.
    Additionally, the SBC supports Syslog log alerting and reporting, so maintenance staff can monitor the device’s operational status and quickly trace issues when an unusual warning occurs.
    Monitoring of SBC core components
    SBC_monitor_2.png
    List of warning categories
    SBC_warning_list.png
    Conclusion
    Generally, the high availability of the SBC can be achieved in several ways with other smart tools. High availability of the SBC can be deployed with hardware models that have different control policies. Dinstar SBC offers a highly performant solution with solid high availability and proven stability, already implemented in many use cases. If you are interested in an HA SBC solution, please email .